Showing posts with label quad multiwii. Show all posts
Showing posts with label quad multiwii. Show all posts

Thursday, October 1, 2015

My MultiWii Settings

Well after a bunch of tweaking and testing, I am closer to a set of MultiWii settings that work for me...


The settings were dialed-in to be sort of a modest flyer.  Since I eventually want to do FPV flying, this is what I was aiming for.

I was very glad that I was able to configure a nice model config file for my Devo 7E.

name=Micro MWC
mixermode=Advanced
icon=FPV-QUAD.BMP
type=multi
[radio]
protocol=DSM2
num_channels=7
fixed_id=123456
tx_power=150mW

[channel1]
safetysw=HOLD1
safetyval=-125
template=simple
[mixer]
src=THR
dest=Ch1
scalar=125

[channel2]
reverse=1
template=expo_dr
[mixer]
src=AIL
dest=Ch2
scalar=125
curvetype=expo
points=15,15
[mixer]
src=AIL
dest=Ch2
switch=SW B1
scalar=80
curvetype=expo
points=20,20
[mixer]
src=AIL
dest=Ch2
switch=SW B0
scalar=60
curvetype=expo
points=25,25

[channel3]
template=expo_dr
[mixer]
src=ELE
dest=Ch3
scalar=125
curvetype=expo
points=15,15
[mixer]
src=ELE
dest=Ch3
switch=SW B1
scalar=80
curvetype=expo
points=20,20
[mixer]
src=ELE
dest=Ch3
switch=SW B0
scalar=60
curvetype=expo
points=25,25

[channel4]
reverse=1
template=expo_dr
[mixer]
src=RUD
dest=Ch4
scalar=125
curvetype=expo
points=15,15
[mixer]
src=RUD
dest=Ch4
switch=SW B1
scalar=80
curvetype=expo
points=20,20
[mixer]
src=RUD
dest=Ch4
switch=SW B0
scalar=60
curvetype=expo
points=25,25

[channel5]
template=expo_dr
[mixer]
src=SW A0
dest=Ch5
scalar=125
curvetype=3point
points=100,0,-100
[mixer]
src=SW A0
dest=Ch5
switch=SW A1
scalar=0
curvetype=3point
points=100,0,-100
[mixer]
src=SW A0
dest=Ch5
switch=SW A2
scalar=125
curvetype=3point
points=100,0,-100

[channel6]
template=simple
[mixer]
src=FMODE1
dest=Ch6
scalar=125
curvetype=min/max
points=0

[trim1]
src=LEFT_V
pos=TRIMLV+
neg=TRIMLV-
[trim2]
src=RIGHT_V
pos=TRIMRV+
neg=TRIMRV-
step=5
value=-7,0,0
[trim3]
src=LEFT_H
pos=TRIMLH+
neg=TRIMLH-
[trim4]
src=RIGHT_H
pos=TRIMRH+
neg=TRIMRH-
step=5
value=23,0,0
[timer1]
type=countdown
src=THR
time=300
[timer2]
type=permanent
src=Ch1
val=11505700
[safety]
Auto=min
[gui-128x64]
V-trim=55,10,1
H-trim=1,59,3
V-trim=69,10,2
H-trim=78,59,4
Big-box=2,26,Ch1
Small-box=2,39,Timer1
Small-box=2,48,Timer2
Bargraph=79,30,Ch1
Bargraph=85,30,Ch2
Bargraph=91,30,Ch3
Bargraph=97,30,Ch4
Bargraph=103,30,Ch5
Bargraph=109,30,Ch6
Toggle=4,11,2,65,129,SW B
Toggle=13,11,0,71,0,None
Toggle=22,11,0,7,0,FMODE
Toggle=31,11,0,0,0,None
Toggle=40,11,0,72,0,HOLD
Battery=102,1

TxPower=75,1


Friday, August 21, 2015

First Micro MWC Build

I have some photos of the first build with the Micro MWC flight control board.






It's a pretty simple build.  I am using a Picnic Frames' "Efficiency Platform" poly-carbonate frame with 4 generic 8x20mm motors.

The quad is flying pretty well now, since I started tweaking it a few days ago.  I loaded a version of MultiWii 2.3 that was hosted by the Micro Motor Warehouse here.  I am using the MultiWiiConf application to do the PID tweaking.

I will post my "final" settings when I am done playing around with them.



Thursday, August 20, 2015

The Micro MWC MultiWii Flight Controller / Receiver Board

I have some quite time now, so I thought I would post some information.

I have been constructing a new quadcopter, trying to use the Micro MWC flight control board I received for my birthday.  Here is a picture of it (enlarged)...



The actual board is not much bigger than a standard SD card.  You can see where the motor connections are at the bottom.  This board has a built-in DSM2 receiver and 4 ESCs for the four motors of my quadcopter.  This FC board is strictly meant to drive brushed motors.

The most interesting part of the board, to me, is that it is a MultiWii flight controller that uses an Atmel AVR chip to run the flight control software.  I have always been interested in MultiWii because 


  1. It allows you to tweak the flight performance of the quad in all sorts of ways
  2. It's actually implemented as an Arduino sketch
  3. It has this cool configuration utility
The first step I am going to take is solder some motor connectors to the board.  I have these micro JST (1.25mm) connectors that I ordered from AliExpress. My hope is that I have polarized my current motor connector to match the orientation that I am going to solder to the board.  I'll post more about this with some photos later.

Finally, I will also have to solder a power adapter to the board.