Well, I had a disappointing evening with respect to my Micro MWC flight control board. I was moving it to a new frame from Picnic Quads and apparently I managed to kill one of the MOSFETs to one of the motors. :-(
I guess I am disappointed because it did not last that long. I only had about 2 hours of flight time with it. I don't think I will replace it immediately. It's rather expensive at $35 from Hobby King and that is about as cheap as they get.
In the meantime, I will just use Hubsan control boards on all my home built quads. At $12 each, I can afford to play with those.
Anyway, I have been re-tooling my FPV Racer quad with the carbon fiber frame. In preparation for the top plate that I should receive in a few days, I have pulled all of the FPV components off of the polycarbonate top plate and cleaned them of extraneous silicone.
Here is the base so far...
At this stage, the quad is a crazy flier... weighing in at just under 30g. This is good because I will need as much power as I can get when I add the FPV stuff back.
I have also begun work on the polycarbonate version... which I think I will use as a practice quad. It will be tougher that the carbon fiber quad, but should have all of the same flight characteristics.
Well after a bunch of tweaking and testing, I am closer to a set of MultiWii settings that work for me...
The settings were dialed-in to be sort of a modest flyer. Since I eventually want to do FPV flying, this is what I was aiming for.
I was very glad that I was able to configure a nice model config file for my Devo 7E.
name=Micro MWC
mixermode=Advanced
icon=FPV-QUAD.BMP
type=multi
[radio]
protocol=DSM2
num_channels=7
fixed_id=123456
tx_power=150mW
[channel1]
safetysw=HOLD1
safetyval=-125
template=simple
[mixer]
src=THR
dest=Ch1
scalar=125
[channel2]
reverse=1
template=expo_dr
[mixer]
src=AIL
dest=Ch2
scalar=125
curvetype=expo
points=15,15
[mixer]
src=AIL
dest=Ch2
switch=SW B1
scalar=80
curvetype=expo
points=20,20
[mixer]
src=AIL
dest=Ch2
switch=SW B0
scalar=60
curvetype=expo
points=25,25
[channel3]
template=expo_dr
[mixer]
src=ELE
dest=Ch3
scalar=125
curvetype=expo
points=15,15
[mixer]
src=ELE
dest=Ch3
switch=SW B1
scalar=80
curvetype=expo
points=20,20
[mixer]
src=ELE
dest=Ch3
switch=SW B0
scalar=60
curvetype=expo
points=25,25
[channel4]
reverse=1
template=expo_dr
[mixer]
src=RUD
dest=Ch4
scalar=125
curvetype=expo
points=15,15
[mixer]
src=RUD
dest=Ch4
switch=SW B1
scalar=80
curvetype=expo
points=20,20
[mixer]
src=RUD
dest=Ch4
switch=SW B0
scalar=60
curvetype=expo
points=25,25
[channel5]
template=expo_dr
[mixer]
src=SW A0
dest=Ch5
scalar=125
curvetype=3point
points=100,0,-100
[mixer]
src=SW A0
dest=Ch5
switch=SW A1
scalar=0
curvetype=3point
points=100,0,-100
[mixer]
src=SW A0
dest=Ch5
switch=SW A2
scalar=125
curvetype=3point
points=100,0,-100
[channel6]
template=simple
[mixer]
src=FMODE1
dest=Ch6
scalar=125
curvetype=min/max
points=0
[trim1]
src=LEFT_V
pos=TRIMLV+
neg=TRIMLV-
[trim2]
src=RIGHT_V
pos=TRIMRV+
neg=TRIMRV-
step=5
value=-7,0,0
[trim3]
src=LEFT_H
pos=TRIMLH+
neg=TRIMLH-
[trim4]
src=RIGHT_H
pos=TRIMRH+
neg=TRIMRH-
step=5
value=23,0,0
[timer1]
type=countdown
src=THR
time=300
[timer2]
type=permanent
src=Ch1
val=11505700
[safety]
Auto=min
[gui-128x64]
V-trim=55,10,1
H-trim=1,59,3
V-trim=69,10,2
H-trim=78,59,4
Big-box=2,26,Ch1
Small-box=2,39,Timer1
Small-box=2,48,Timer2
Bargraph=79,30,Ch1
Bargraph=85,30,Ch2
Bargraph=91,30,Ch3
Bargraph=97,30,Ch4
Bargraph=103,30,Ch5
Bargraph=109,30,Ch6
Toggle=4,11,2,65,129,SW B
Toggle=13,11,0,71,0,None
Toggle=22,11,0,7,0,FMODE
Toggle=31,11,0,0,0,None
Toggle=40,11,0,72,0,HOLD
Battery=102,1
TxPower=75,1
